Showing posts with label flow meter calibration. Show all posts
Showing posts with label flow meter calibration. Show all posts

Tuesday, October 12, 2021

What is Flow Meter Calibration?

A flow meter is a test device used to calculate the flow rate of process fluids and gases in industrial plants and facilities. The flow rate denotes to the speed at which a process fluid is moving through pipelines, orifices, or vessels at a given time. Control and instrumentation engineers measure this value to screen and regulate the speed and efficacy of industrial flow processes and devices.

Ideally, test devices must be ‘reset’ from time to time to stop having inaccurate readings. For example, a bathroom scale that indicates 10lbs when nobody is standing on it needs to be recalibrated to specify an initial zero value.

In industrial settings, Liquid Flow Calibration is performed to ensure that measurements are accurate permitting operations to proceed in a safe and timely manner.

What is Flow Meter Calibration?

Flow meter calibration is the procedure of comparing the pre-set scale or metering of a flow meter to a standard scale of measurement and adjusting its metering to conform to the standard. Calibration is a vital aspect of instrumentation in a broad range of industries that require high-accuracy measurements with a tiny percentage of error e.g. in Oil & Gas, Petrochemical, and manufacturing.



Flow meters are calibrated by comparing and adjusting their metering to agree with a predefined standard. Flow meter manufacturers normally calibrate their products in-house after production or send them to an independent calibration facility for adjustment.

Flow meter calibration comprises comparing the measurements of a flow meter in operation to that of a standard flow measurement device under the same conditions and regulating the scale of the flow meter to be in close agreement with the standard.

Process Flow Calibration involves calibration of a flow meter which is at present in use. Periodic recalibration is needed as flow meter readings will often go ‘out of phase’ over time due to variable conditions involved in industrial processes.

The main difference amid the two procedures is that flow calibration is done before the meter is sent out for use while recalibration is done after the flow meter has been in operation for a while. Software tools can also be used to verify the correctness of measurements after a flow meter has been calibrated.

 


Friday, June 4, 2021

Exactly how to Calibrate a Flowmeter?



A flowmeter is a tool that is used to measure the flow rate of a gas or fluid and then shows the flow reading to the instrument operator by means of an indicator, either analog or digital output. In general, flowmeters offer vital measurement data to industry types, from pharmaceutical to Oil & Gas. The flowmeter types used here refer to closed pipe type flowmeters and not open channel systems. The flow rate denotes the average velocity at which a gas or fluid moves through the pipe. To guarantee the flow meter indicates or outputs a reliable and precise reading, the flowmeter must be calibrated consistently.

What is Flow Meter Calibration?

Calibration is the procedure of checking an instrument to check it is correct. Flowmeter calibration is the same method where the measurement is flow. Calibration of a flowmeter can be attained in one of the numerous ways, but generally includes the comparison of the flowmeter against a reference standard of higher precision. Calibration is a crucial part of an instrumentation system to promise a line of traceability of the measurement system is maintained. To understand the flowmeter performance over a period of time, flowmeter calibration must always be conducted on an “As Found” basis so meter drift analysis can be measured. With additional customer agreement, a further adjustment of the flow meter reading may be performed to reduce the flowmeter errors.

Flowmeter Calibration Processes?

We describe the various flowmeter methods and procedures associated with liquid flowmeters. Then will discuss the calibration methods for air and gas flowmeters. Liquid flow calibration can be done in numerous ways, but always includes the comparison against a standard, this may be a primary or secondary reference standard, dependent upon the precision required. The three central calibration principles for the Process flow meter calibration system use Gravimetric, Volume or transfer standard calibration methods. 

Saturday, October 24, 2020

Positive Displacement Flow Meters From Nagman Flow

Positive Displacement flow meters are the best flow measuring equipment to openly measure the volume of fluid that travels through the flow meter. It attains this by trapping pockets of fluid amongst rotating components housed inside a high precision chamber. This can be associated to recurrently filling a beaker with fluid and pouring the contents downstream while calculating the number of times the beaker is filled. Rotor rotational velocity is directly related to flow rate since the flow of fluid is instigating the rotation.




 

 In the case of electro magnetic flow meters, the rotating components involve magnets that trigger numerous sensor options located exterior to the fluid chamber. Mechanical positive shift flow sensors rely on the rotation to drive either a magnetic coupling or a direct gear train related to the mechanical counter.

 

 Positive Displacement flow meters do not gratify a power supply for their operation and do not need straight upstream and downstream pipe runs for their setting up. Positive displacement flow meters are obtainable in sizes from in to 12 in and can function with turndowns as great as 100:1, although ranges of 15:1 or lower are much more communal. The slippage between the flow meter constituents is reduced and metering precision is consequently increased as the thickness of the process fluid increases.

 

 The process fluid must be spotless. Particles greater than 100 microns in size must be detached by filtering. PD meters work with small clearances amid their precision-machined parts which worn out speedily and rescind their accuracy. For this reason, Positive Displacement flow meters are generally not suggested for measuring slurries or coarse fluids. In fresh fluid services, nevertheless, their precision and wide rangeability make them perfect for custody transfer and group charging. They are most extensively used as household water meters. Millions of such units are formed annually. In industrial and petrochemical applications, Positive displacement flow sensors are normally used for batch charging of both liquids and gases.

 

 While slippage through the positive displacement flow meters declines that is, correctness increases as fluid viscosity increases, the pressure drop through the meter also increases. Subsequently, the maximum and minimum flow capacity of the flow meter is reduced as viscosity surges. The greater the viscosity, the less slippage and the lesser the measurable flow rate becomes. 


Tuesday, September 15, 2020

Nagmanflow's Flow Meters and the complete study

         A flow meters is a device used to calculate the linear, the nonlinear, mass and volumetric flow rate of a fluid or a gas. When selecting the flow meters, one ought to think about such subtle factors as expertise of plant personnel, their knowledge with calibration and maintenance, spare parts accessibility, and meantime linking failure history, etc., at the particular plant site. It is also suggested that the cost of the installation be calculated only after taking these steps.




     One of the most general flow measurement mistakes is the reverse of this sequence: instead of picking a sensor which will execute correctly, an effort is made to justify the use of a device since it is less expensive. Those "inexpensive" purchases can be the most expensive installations. This blog will help you comprehend flow meters, and you can also converse to our application engineers at any time if you have any particular flow measurement challenges.

  

        The primary step in flow sensor variety is to resolve if the flow rate information should be constant or totalized and should consider if this information is required locally or remotely. If a little, how should the transmission be? Should the transmission be analogue, digital, or shared? And, if shared, what should be the minimum data-update frequency. And if an answer is derived from the question, an assessment of the properties and flow uniqueness of the process liquid, and of the piping that will house the flow meter, must take place. To come up to this task in a methodical manner, forms have been developed, so that the following types of data are entered for each application.

  


 

 

    The fluid and its specified pressure, temperature, permissible pressure drop, density, conductivity, viscosity and vapour pressure at highest operating temperature are listed, jointly with a suggestion of how these properties might vary or interact. In toting up, all security or toxicity levels should be provided, collectively with exhaustive data on the fluid's composition, presence of bubbles, solids, tendency to coat, and light transmission qualities.

 

    Probable minimum and maximum pressure and temperature values must be given in adding to the usual operating values whilst choosing flow meters. Can the flow reverse, will it always fill the pipe, does the slug flow can develop air-solids-liquid, if aeration or pulsation is probable, can the sudden temperature changes can happen, or only particular precautions are required throughout cleaning and maintenance, these particulars, too, should be confirmed.


       Regarding the piping and the region where the flow meters are to be located, consider: For the piping, its course must avoid downhill flow in liquid applications, size, material, and schedule. The engineer ought to identify if vibration or magnetic fields are present or likely in the area if electric or pneumatic power exists, if the spot is classified for explosion hazards, or if there are previous exceptional requirements such as observance with sanitary or clean-in-place (CIP) regulations.

Friday, August 14, 2020

PROCESS FLOW METER CALIBRATION SYSTEM

 The Flocal Series by Nagman Instruments Consortium, a PAN India Company, sizes in meters from DN10 up to DN 400 with many more sizes presented to you. It provides a good flow rate between 1 to 25000 LPM or more depending on your requirement.

In order to make sure it suits, the ProcessFlow Meter Calibration System comes with 1, 2 or 3 lines, providing a Calibration Campaign Time from 30 seconds.

The Process Flow meter Calibration System comes with different Calibration Methods such as Gravimetric or Volumetric or Comparison with accuracies ranging from 0.2% to 0.05%.

Water, the correction factor for other liquids serves as the Calibration Media. The number of units to test depends on what suit the best – Single or Multiple.

The display or control console as some call it directs the Flow Rate, Total Flow, Start/Stop Timer and a lot more all operated Manually; Semi or Fully Automatically. Any of the operations methods could be used depending on the convenience.

The automation functions as PLC; HMI or SCADA. On the other hand, System Modules include Pumps with VFD/ Distribution Headers / Mounting Clamps / Spacers – Reducers, Adapters / Electro-Magnetic Meters (Flow Setting Masters) / Valves / Measuring Tanks / Flow Diverters / Weigh scales, Load Cells / Storage Tanks++.

Each best suited for Calibrating Flow Elements/ Electromagnetic/ Mass/ Vortex/ Ultrasonic/ PD Type Flow Meters.

The company, Nagman Instruments Consortium, was founded in the year 1972 serving the global market ever since. The organisation offers Comprehensive Calibration Solutions to customers through its various branches. The company jostles with a vision to identify niche avenues and potentials across the globe and enhance the business in the Filed Instruments and Calibration Systems.

Sunday, October 20, 2019

Flow Meter Calibration system


Flowmeter calibration can be divided into four sections, namely level, liquid, gas & mobile flow calibration meters.

Level calibrations use Electrical / Electronic and Pneumatic Consoles are housed in a sleek Panel / Test Bench Rack, designed ergonomically; a stand-alone Hydro (Water) Intensifier Unit caters to Pressure Tests. With Built-in Intelligent Software (with the facility of Retrieving / Recording / Interpreting & Displaying the Readings / Values received from various Test and Standard Instruments in easily understandable/user-friendly format) is provided for generation of Calibration Certificate / Chart / Report.
 Types of level Instruments –best Suited for
Tests that can be performed
                               Float type level instruments
                            Linearity
                               Displacer
                            Dead band
                               Radar
                           Sensitivity & Resolution
                               Capacitance
                            Pressure test
                               Ultrasonic
                            Hysteresis
                               Magnetic
                            Repeatability
                            Built-in & External chamber
                            Functional
.
Nagmanflow’s Water meter calibration system is most suited for verifying / Calibrating – Domestic Water Meters of Sizes from DN 15 to DN 50 and Bulk/Industrial meters of Sizes above DN 50 up to DN 300.
Complete Integrated System with Pumps (with VFD), Rotameters or Flow meters / Manual or Automatic Throttles for Flow Rate Control. Reservoir, Test Bed with Quick Clamping Systems / Spacers & Blanks and Electric Control Console / Calibration Software.
Boon to Water Boards / Jal Nigam / Municipal Corporations / OEMs & Calibration Labs
Best Suited for Single JET, Multi Jet, Electromagnetic and Ultrasonic water meters covering AMI / AMR features.
Nagmans gas Calibration Standard’ of the Test Bench is “Bell Prover”, which is considered a Primary (Calibration) Standard to Test & Calibrate Domestic Gas Meters (& Gas Meters used in Hotels/Restaurants etc.). The device is ideal for OEMs, Calibration Laboratories & Calibration Service Providers.
The Test Bench, with 2 Sizes of Bell Prover (20L & 100L)will effectively cover Very Low (Qmin – typically 0.016 m3/h (0.27 LPM)) to Maximum (Qmax – 6 m3/h (100 LPM)) Flow Rates. Available Accuracies : 0.2% & 0.5% F.S.
Upto 4 Gas Meters can be connected (inserted) during a campaign. Facility provided for continuously monitoring Differential Pressures (DP) across each Meter as well as upstream & downstream Line Pressures & Line Temperatures. Line Pressures are regulated typically around 500Pa.
Nagman’s BELL PROVER

Bell prover helps the gas flow meter test bench to sample and calibrate the gas flow. It can test rota meter, gas meter, and other forms of a gas flow meter. The bell prover can move up and down automatically and the gas-output valve can switch automatically.
The Bell prover and liquid cell form a sealed space of variable volume. When the Bell moves down into the sealed liquid, through pressure compensation mechanism, the internal gas pressure does not vary along with the changed depth of the sealed liquid. Meanwhile, the gas in the Bell is exhausted to the flow meters through a connect pipe. The exhausted gas volume will be detected compared with the cumulative in the meters.
Sizes
  G 1.6 to 6
Working pressure
  1 KPa to 5 KPa
Flow range
  0.2 m3 / hr. to 120 M3/hr
Accuracy
  0.2 to 0.2%

Nagmanflow’s Sonic Nozzle

A “sonic nozzle” (also known as “Critical Flow Venturi” or “Critical Flow Nozzle”) is a flow meter that can be used as a calibration standard for gas flow meters or any flow measurement device. By design, sonic nozzles are a constant volumetric flow meter.
The nozzles are designed and manufactured to the ISO standard and as such the gas is accelerated along the Bell Mouth converging section and then is expanded in a conical diverging section, which is designed for pressure recovery. In the throat or minimum area point of the Sonic Nozzle, the gas velocity becomes equal to the speed of sound. At this point, gas velocity and density are maximized, and the mass flow rate is a function of the inlet pressure, inlet temperature, and the type of gas. So, you only need to measure the inlet pressure and temperature to determine the flow rate.